Showing results: 3361 - 3375 of 4427 items found.
-
RI 7100A -
Roos Instruments, Inc.
The RI 7100A, which RI has shipped for over 10 years, has proven itself as the most advanced, reliable (> 4500 hours MTBF) and cost effective RFIC ATE System available. "Our recipe for high performance microwave test has always been dependent on an extremely elegant RF signal path while maintaining the most advanced microwave calibration software," said RI President, Mark Roos.
-
Environment Associates Inc.
Products with moving parts, electromechanical components, filtering systems and electronics are all susceptible to fine and large particle dust that can contaminate a product. These contaminates can cause premature failures and loss of function.Today’s test plans for phones, computers, vehicles, enclosures and aircraft include sand and dust testing to determine if this stress source would cause functional deterioration.Our services include military and automotive dust testing for both blowing and agitated dust and sand.
-
782131-01 -
NI
Slave, C Series PROFINET Slave Interface Module - The cRIO-PN-S connects NI programmable automation controllers (PACs) to PROFINET industrial networks as powerful slaves. The interface includes the NI‑PROFINET for CompactRIO driver for human machine interface (HMI) and supervisory control and data acquisition (SCADA) applications. You can perform PROFINET device automated test using these interfaces. The cRIO-PN-S is only compatible with CompactRIO systems.
-
780993-03 -
NI
200 MHz, 32-Channel PXI Digital Waveform Instrument—The PXIe‑6545 is a digital waveform generator and analyzer for interfacing with 32 single-ended digital pins. The device is capable of sampling digital waveforms at up to 200 MHz and interfacing with common transistor‑to‑transistor logic (TTL) voltage levels. The PXI‑6545 also features advanced synchronization capabilities for building integrated mixed-signal test systems and per-bank digital timing features.
-
Phenix Technologies
Designed to generate impulse voltages that simulate lightning strokes andswitching surges as defined by IEC, ANSI/IEEE, and other national standards on:• Distribution transformers• Small power transformers• Cables (type tests)• Arrestors (impulse current tests)• Motors / generatorsTesting ApplicationsImpulse Generators andMeasurement Systems• Insulators• Bushings• GIS• Instrument transformers
-
EE-120A-3S + EE-500V-3 -
EMSYST Ltd
The Phantom Load is able to generate three-phase voltages and currents with unprecedented stability and measurement accuracy. The amplitude and phase-shift of each current and voltage is individually adjustable. All types of electricity meters – mechanical or electronic, for active, reactive or apparent energy, single-phase or three-phase – can be tested with the Energy Standard. The following meter tests can be carried out with the EE Test System: Error Test, Register Test, No Load Test and Starting Current Test. Full analysis of the customer load can also be performed, if current clamps have been ordered. All test results ( maximum 3 Test Plans, 5 Manual Measurements and Customer Load Analysis) can be saved in one file. 100 saved files can be viewed on the LCD display or transferred to a PC via USB port.
-
AS7265x (Qwiic) -
SparkFun Electronics
The SparkFun Triad Spectroscopy Sensor is a powerful optical inspection sensor also known as a spectrophotometer. Three AS7265x spectral sensors are combined alongside a visible, UV, and IR LEDs to illuminate and test various surfaces for light spectroscopy. The Triad is made up of three sensors; the AS72651, the AS72652, and the AS72653 and can detect the light from 410nm (UV) to 940nm (IR). In addition, 18 individual light frequencies can be measured with precision down to 28.6 nW/cm2 and accuracy of +/-12%. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
NovoTest
Digital Brinell Hardness Tester NOVOTEST TB-B-C has 10 steps testing force settings, allows user to measure hardness values with each of 10 Brinell hardness scales. The device uses the round type of indenter along with the control system. It is highly accurate, gives repeatable results, reliable and easy to operate.Digital Brinell Hardness Tester NOVOTEST TB-B-C has fully automatically test cycle: loading, dwell and unloading. As a result, the operator errors don’t influence on measuring results.Motorized indenter and electronic control system allow making measurements with high accuracy. Absence of mechanical weighs reduce problems of friction and vibration sensitivity of the machine.
-
LXinstruments GmbH
The hipot test (high potential test) or dielectric withstand test, is used to determine the insulation and dielectric strength. It is carried out on modules, devices and systems of protection class I + II. In this test, the insulation of the test object is subjected to greater stress by the high voltage than in normal operation. It is determined whether the insulation of all current-carrying conductors, as well as the safety distance to the enclosure, is sufficient and complies with the legal requirements under normal operating conditions.We will be happy to assist you with any questions or solutions to problems.You will find a large selection of high-voltage testers in our comprehensive shop.Questions? We are always at your disposal.
-
STAr Technologies, Inc.
STAr provides cost effective semiconductor ATE test systems for linear, power management and mixed signal devices and ensures industry customers attain the highest level of return-on-investments and satisfaction.
-
V&V Services -
Rapita Systems Ltd.
*Unit and integration testing*System and acceptance testing*DO-178 process definition and optimization*Test automation*Timing analysis and optimization*On-target problem solving*Third-party software verification*Assurance services
-
1669 -
Peaceful Thriving Enterprise Co Ltd
Check on 6 and 12V systems, test for circuit and spark plug.1. Check spark plug on secondary or high voltage. 2. Use as a continuity tester to check on low voltage circuits.
-
TEST-330B -
Beijing GFUVE Electronics Co.,Ltd.
Three phase secondary current injection test set is testing relay set, protective device, instruments, output ac dc current and voltage source, embedded Window XP system.
-
RP7972A -
Keysight Technologies
The RP7972A regenerative power system is a single output, bi-directional, regenerative DC power supply with highly integrated safety features that protect both your people and your device under test.
-
RP7983A -
Keysight Technologies
The RP7983A regenerative power system is a single output, bi-directional, regenerative DC power supply with highly integrated safety features that protect both your people and your device under test.